At Hunt we’re just like all other cyclists and so have spent many years fiddling with bikes, wheels and tires. Over the course of time we have often had to learn the hard way, with a fair amount of trial and error and head scratching. There is plenty of useful information that can save you loads of time and we realise that you have a life outside of cycling and don’t necessarily want to spend hours researching how to set up tubeless tires or comparing wheel specifications to find the perfect product for your exact needs. To help you we will be creating a number of ‘how to’ videos exploring the more practical side of wheel ownership as well as a series of videos explaining some of the concepts and features behind our purpose driven wheel range development.

In this article we will take you through the easy steps to fitting tubeless road tires to tubeless road bike rims and tell you the hints and tips we’ve picked up through our many years setting up tubeless.

Tubeless tire technology has been popular in the Mountain Bike world for a number of years. The ability to run lower pressures to improve grip and reduce rolling resistance without the risk of pinch punctures, the lower rotating mass and puncture sealing capabilities of tire sealant have all helped make tubeless technology the preferred choice for Mountain Bikers.

However Road Bike Tubeless technology has taken longer to be adopted, mainly due to the traditional use of Tubular tires inside the professional peloton holding back adoption and a lack of good information making it seem like somewhat of a black art! We think this is a shame as, while tubeless isn’t for everyone, many cyclists would benefit from the real world practicality and performance it can deliver.

Road bike tubeless technology is based on the traditional clincher tire and inner tube system with one major difference, there is no inner tube! Effectively the inner tube is removed and the tire is manufactured to be air tight. The difference between a traditional clincher tire and road bike tubeless tire is that the bead (i.e the section that holds onto the rim) needs to be air tight and that they are slightly thicker due to the air tight layers used in the construction. The tubeless road bike rim is also slightly modified compared to a traditional clincher rim. All of our Hunt Wheels use a tubeless road bike rim featuring horizontal tubeless shoulder steps which are different to a normal clincher rim which has a single curve from edge to edge (see photo comparison below). This step ensures that the bead of the tire is held in place safely and securely so that air cannot escape.

The other factor that needs to be considered is sealing the spoke holes on the inside of the tubeless road bike rim. This is solved by using a tubeless rim tape. Effectively this is tough sticky tape that sticks to the rims covering the spoke holes and preventing air from escaping.

A tubeless valve is then used, similar to a standard inner tube valve but with a rubber base that pulls tight against the valve hole allowing air to be pumped into the tire.

The magic ingredient to complete the tubeless recipe is liquid latex tire sealant. Tire sealant is poured into the tyre and covers all the internal surfaces and helps prevent any air leakage. It also has the major benefit of sealing most punctures, often without you even realising!

In order to help you we have produced a comprehensive video guide to thoroughly explain how to fit tubless tires. Alongside the video we also have a written guide.

• A set of Tubeless Ready wheels
• A pair of Tubeless Valves
• A roll of Tubeless rim tape
• A bottle of Tubeless Tire Sealant
• A pair of Tubeless Ready road bike tires
• A set of tire levers
• A pump
• A cloth
• Alcohol cleaner
• A cocktail stick (or similar narrow pointed object)

As previously mention the tubeless rim will need to be sealed i.e. the nipple holes covered to prevent air escaping. The first stage is to ensure that the internal rim surface is cleaned of contaminants. This is done by wiping around the internal rim surface with the alcohol cleaner and cloth. This ensures that the tape sticks firmly to the inside of the rim. Once the rim is clean it’s time to apply the tape. Start one spoke away from the valve hole and begin to stick the end of the tubeless tape to the rim. Ensure that you pull the tape as tight as possible, rubbing the tape down with a cloth ensuring it sticks to the rim. We recommend two layers of tape when using our Hunt Bronze tape, our tape is designed to be light weight and flexible to create the best seal, some heavier tapes may only suggest one layer in their instructions. Once the two layers of tape have been applied, visually check that all the valve holes have been covered and then give the tape a final rub with a cloth ensuring it is well adhered to the rim surface all over. Finally pierce a small hole in the rim tape over the valve hole using a cocktail stick, spare spoke, or something similar.

In order to inflate the tubeless tire you will need to insert the tubeless valve into the rim. Take the tubeless valve and unscrew the plastic cap and lock ring. Tighten the valve head so it doesn't get damaged. Then from the inside of the rim push the head of the valve through the small hole in the rim tape (that you made in step 2) and through the rim. At this point you can run some sealant round the base of the valve to help ensure sealing. Then screw the valve lock ring on to the valve so that it pulls the base of the valve tight against the inside surface of the rim.

Now it is time to fit the tire. If there is direction arrow on the tire side wall make sure the tire is facing the correct rotation direction, although slight road tires often don't have specific rotation direction. Fit one side of the tire bead to the tubeless rim, you may require a tire lever for this. If you do use a tire lever make sure not to damage the rim tape, especially near the valve or spoke holes. If it is hard to fit make sure that the bead of the tire is sitting in the central dipped well of the rim, this will make it easier to get the last bit of the tire bead over the rim. Now proceed to fit three quarters of the bead on the other side of the tire.

With the tire almost fitted (don’t forget the second side of the tire should be three quarters fitted) it’s time to add the tire sealant. Shake the bottle of tire sealant to ensure it is mixed and pour 35ml into the opening in the tire bead. Rotate the wheel so that the liquid cannot leak out of the opening and then pop the rest of the tire bead into place, again you may require a tire lever for this. Then slowly rotate the wheel and angle to ensure the sealant coats all the internal surfaces of the tire and rim. At this point you can run some additional sealant around the tyre bead to help ensure a perfect seal.

Now that the tire is fitted and sealant added its time pump them up. Tubeless tires require a blast of air to ensure that the tire bead seats in the rim right away. This can be done by frantically pumping a floor pump but is much easier with a compressor of one of the new style of air chamber floor pump. We favour the air chamber floor pump, effectively a floor pump with an air chamber attached that holds compressed air which can then be released in one quick blast. So firstly charge the air chamber on your floor pump by pumping it up. Then attach the pump head to the tubeless valve on your wheel and release the compressed air on your pump. This blast of air should seat the tire on the rim. You may find that some air escapes initially but the tyre sealant should plug the gap (a spin of the wheels may be needed to spread the sealant again). Once the tire is sealed pump the tyre up to the required pressure, fit them to your bike and get out and ride!